The autocutter has two opposing cutter blades that operate like a scissors to cut the paper. Remove 2 screws circled on the photo and all the connections between printer mechanism and main circuit board. Page 36 The following shows the locations of the main elements on the main circuit board unit. Make sure a paper roll has been installed properly. Dirt, lint, dust Use a vacuum cleaner to completely remove all dirt, lint, and dust.

Uploader: Vigor
Date Added: 19 September 2015
File Size: 69.29 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 69051
Price: Free* [*Free Regsitration Required]

Take ultra-vast paper roll out of the printer when thhermal will ultra-fast receipt thermal printer tm200 use the printer for a long time in a high temperature and humidity environment. The printer executes the following operations upon detecting an error. Page 13 Cutter setting Stop bit Cutter mode Reserved: Interfaces RS serial interface Specifications: Control Panel Control Circuit This control panel is located on the mainboard.

Then unplug each motor or coil’s connector from the main board one by one; plug the printer back in, and power it on. Error Types And Processing The printer executes the following operations upon ultra-fast receipt thermal printer tm200 an error.

Epson TM200 Service Manual

Reverse the printer, move the body cover apart. Data Receive Error only with the serial interface model If one of the following errors occurs during serial interface communications, the printer ignores the data Parity error Framing error Overrun error Would you use this site again?: Finally my PC got up to speed! Autocutter Module This printer is equipped with an autocutter module for cutting of the roll paper and a manual cutter for manual cutting. Don’t show me this message ultra-fast receipt thermal printer tm200.

High Speed Thermal Receipt Printer TM,Brendale,Strathpine,Brisbane

Main Circuit Board 1. TM Service Manual 6. The following shows the locations of the main elements on the main circuit board ultra-fast receipt thermal printer tm200.

Doing so can cause the cutter blade to be exposed, making it impossible to open the paper roll cover.

To install, reverse the removal procedure. Door Sensor Block 1. It is a separate cutter blade-type mechanism that does not require passage of the roll paper through an autocutter mechanism slit.

If you do not follow them, it could cause an autocutter operation failure. Paper Precautions Take the paper roll out of the printer when you will not use ultra-fast receipt thermal printer tm200 printer for a long time in a high temperature and humidity environment. When ultra-fast receipt thermal printer tm200 procedures, be sure to use a grounded ulgra-fast band or take other measures to protect against electrostatic charge. Switch Circuit Board Assembly TM Control Circuit Thermal head driver circuit The print head of the receipt printer mechanism thermzl a thermal type print head with dots per line.

Page 22 The paper outlet ultra-fast receipt thermal printer tm200 the printer is covered, and even if paper output becomes blocked for some reason, there is enough room in the space between the platen and frame cover for accumulation of two or three normal length receipts the length of one sheet is assumed to be 80mm or less.

Emi And Safety Standards Applied 15 million lines. All print head control is performed via a gate array.

Pull out a small amount of paper, as shown. Approximately mm 7. Page 10 When the cover is open Printed an error has occurred When the printer stops printing due to a paper-end in cases when an empty paper supply is detected by either paper roll end detector or tehrmal paper roll near- end detector with a printing halt feature using Then, you can depart printer mechanism from its main board.

Make sure a paper roll has been installed properly. The panel lights can tell you a lot of information about the situation of the printer, please refer to Appendix C for details. Appendix D Parts Number List Parallel printer cable, white color, 36 pin Parallel printer cable, black color, 36 pin Serial RS 32K buffer port interface board Serial printer cable, white color, 9 to 25 pin Serial printer cable, black color, 9 to 25 pin USB port interface board Cover Open Button When ultra-fast receipt thermal printer tm200 cover open button located to the right of the cover is pressed, the printer cover is opened.

Move the 2 screws are circled indicated on the photo. Remove the connections from circuit board. Disassembly of some parts and blocks may be ultra-fast receipt thermal printer tm200 unless performed in accordance with the procedures described in this manual.

Take care not to touch the print head.

Ultra Fast Receipt Printer Tm200

Correct the problem that caused the paper jam and reload the paper roll into the unit. Comments to this Manuals Your Name. Ultra-faast 40 TM Service Manual 4. Tm Disassembly, Assembly, And Adjustment 5. Clearing Paper Jams 4. Then close the cover – 27 Close the cover and turn off the printer or reset it to turn ultra-fast receipt thermal printer tm200 the hex pronter mode. Installation Manager Success Stats: Transmit data to the printer after turning on the power and initializing the printer.

Page 45 TM Service Manual 4. Troubleshooting, Symptoms And Solutions 2. Reverse printwr printer, take the body cover apart. Page 29 TM Service Manual 4.

Download Drivers • Information

Note that the thermal head becomes very hot during normal operation, creating the danger of burn injury. In order to connect Printef port, the host setting should be set as: Loose 4 screws beside the thermal cover and move them.

The autocutter has two opposing cutter blades that operate like a scissors to cut the paper.